INSTRUCTIONS
5
2 INSTALLATION
1. Select location for the console and switch-box
that is in easy access and in clear view of the
operator. Ensure that the console and switch-
box will be free of moisture, direct sun, and
excessive vibration.
2. Use the provided large ball and socket to
mount the X30 console.
3. Use the provided small ball and socket to
mount the in-cab keypad. (ball and socket was
not included with early units).
4. Make the following harness connections:
a. Connect X30 Single Key
and X30 Dual
Key connectors on X30 main harness
(3132-12-01, Figure 5) to the CAN ports
on the back of the X30 console, refer to
Figure 1.
b. Connect Battery Power connector on X30
main harness (3132-12-01,
Figure 5) to 3-
pin AMP auxiliary power connection in the
cab (if exists).
c. If the auxiliary power connection does
not exists in the cab, connect X30 power
extension harness (3132-04-03,
Figure 3)
and route/connect to battery.
d. Connect RS232-D (COM 1)
connector
on X30 main harness (3132-12-01, Figure
5) to GPS adapter harness (3132-04-04,
Figure 12). DB9 connector on GPS adapter
harness (3132-04-04) connects to GPS.
Deutsch 3pin plug on GPS adapter harness
is not used.
e. Connect CAN 1 connector on X30
main harness (3132-12-01, Figure 5) to
connector on ISOBUS in the tractor cab.
Refer to images for specific tractor models
in Section 4 - Location of Tractor ISOBUS
Connection Point.
f. Remove CAN 1 terminator and connect
Can 1 Terminator
connector on X30
main harness (3132-12-01, Figure 5) to
connector on X30 ISOBUS adapter harness
(3132-62).
g.
Connect X30 ISOBUS adapter harness
(3132-62) to the ISOBUS in the tractor cab.
h. COM 2 connector on X30 main harness
(3132-12-01, Figure 5) can be connected to
any device that requires signal from GPS,
but is not directly connected to GPS.
i. Connectors on X30 main harness (3132-
12-01, Figure 5) labeled Radar, Remote
Mapping, and CAN 2 are not used.
j. Connect the end labeled "calibration" on
the in-cab switchbox harness (3132-41,
Figure 7) to the Switchbox and plug the
other end into the 9-pin AMP ISOBUS
connection (if it exists).
k. If the 9-pin AMP ISOBUS connection
does not exist in the tractor, use switchbox
ISOBUS adapter harness (3132-42) to
connect into ISOBUS in the same location
as X30 console.
l. Connect switchbox power harness (3132-
76) to switchbox ISOBUS adapter harness
(3132-42) and connect the other end to the
"Switched Power" connector on the X30
harness (3132-12-01).
m. Early units were sent out with a 3132-72
power harness that connected onto 3132-42
and the other end had individual wires. The
switched power wire needs to be connected
to a keyed power source and the ground
wire to a ground source. Alternatively it
can be wired up to the "Switched Power"
connector on the X30 harness.
n. Connect the end labelled 12V Battery "+"
from 3132-87 to positive battery terminal.
Connect the other end labelled 12V Power/
Relay to the 3132-89 relay.
o. Mount the relay near the battery where it
will be protected and the contacts will not
be shorted.
p. Connect the end labelled Battery/Frame
Ground from 3132-88 to the negative
battery terminal. Connect the end labeled
12V Power/Relay to the relay. Connect the
end labelled Power Relay Coil to the relay.
Route the other end to the hitch point and
mount using mount plate (5210-65).
(32 páginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais