CAB Apollo 1 Especificações Página 145
- Página / 234
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
- ATTENTION: - Read the SAFETY REGULATIONS (contained in this manual) carefully for the safety of all personnel and your vehicle.
C/69
Alarm
code
Description What to do
35
Load cell A:
Thermal calibration not present error
Contact the after-sales technical assistance
36
Load cell A:
Check error on LIN bus message
Contact the after-sales technical assistance
37
Load cell A:
CRC error of transmitted data
Contact the after-sales technical assistance
38
Load cell A:
LIN bus message receipt error
Contact the after-sales technical assistance
39
Load cell A:
LIN bus message control hour meter error
Contact the after-sales technical assistance
41
Load cell B:
CRC error of the internal parameters of the load sensor
Contact the after-sales technical assistance
42
Load cell B:
Out of scale signal reading error (10-990)
Contact the after-sales technical assistance
43
Load cell B:
Out of scale internal offset reading error (526-586)
Contact the after-sales technical assistance
44
Load cell B:
Internal 5Vdc power supply voltage error
Contact the after-sales technical assistance
45
Load cell B:
Thermal calibration not present error
Contact the after-sales technical assistance
46
Load cell B:
Check error on LIN bus message
Contact the after-sales technical assistance
47
Load cell B:
CRC error of transmitted data
Contact the after-sales technical assistance
48
Load cell B:
LIN bus message receipt error
Contact the after-sales technical assistance
49
Load cell B:
LIN bus message control hour meter error
Contact the after-sales technical assistance
51 Difference too high between load cell A and B reading Perform calibration test
52
Difference too high between load percentages detected
from channel 1 and 2
Perform calibration test
61
Double safety input congruency error for ground stabilisers
reading.
Contact the after-sales technical assistance
62
Double safety input congruency error for closed
boom reading.
Contact the after-sales technical assistance
63 Inputs congruency error from mode selector Contact the after-sales technical assistance
64 Exclusion key input active upon start-up error Contact the after-sales technical assistance
65 movements re-arm input in active block upon start-up error. Contact the after-sales technical assistance
66 Feedback in frequency signal reading error Contact the after-sales technical assistance
67 Feedback signal reading error of external actuator 1 Contact the after-sales technical assistance
68 Feedback signal reading error of external actuator 2 Contact the after-sales technical assistance
71 Analogical signal reading error from out of scale joystick Contact the after-sales technical assistance
72
Pressure transducer reading error for re-arm verification
with joystick
Contact the after-sales technical assistance
73 CAN BUS messages receipt from optional external unit error Contact the after-sales technical assistance
81 Buttons pressed upon switch-on error Contact the after-sales technical assistance
- MAINTENANCE MANUAL 1
- OPERATION AND 1
- Cod.: AXH1147/UK 3
- CHAPTER “A” 5
- CHAPTER “B” 5
- CHAPTER “C” 7
- CHAPTER “D” 7
- MAINTENANCE AND REGISTRATION 7
- Mod. Apollo 10
- GUARANTEE 11
- VEHICLE IDENTIFICATION 11
- INTRODUCTION 11
- FAC-SIMILE 19
- SAFETY REGULATIONS 21
- - DANGER 22
- - WARNING 22
- - PROHIBITION 22
- - NOTE 22
- GENERAL WARNINGS 23
- PREPARATION FOR EMERGENCIES 25
- DRIVER’S CAB 27
- STARTING UP THE VEHICLE 29
- ENVIRONMENTAL CONDITIONS 29
- - ATTENTION 31
- PARKING THE VEHICLE 35
- TEMPORARY HALT 35
- HOISTING THE MACHINE 37
- TRANSPORTING THE MACHINE 37
- CLEANING YOUR MACHINE 41
- FIRE PREVENTION 43
- TIGHTENING WHEEL NUTS 47
- STORING DANGEROUS FLUIDS 49
- CONTACT WITH DANGEROUS FLUIDS 49
- ROPS-FOPS CAB 59
- BAR 4,5BAR 4,5 69
- AXA 1506 71
- DEXTRON 2 71
- AXA 1492 71
- GETTING TO KNOW AND 73
- USING THE VEHICLE 73
- HAND SIGNALS 77
- External cab components 79
- Internal cab components 79
- INTERIOR CAB INSTRUMENTS 87
- I CELL 89
- MULTI-FUNCTION LEVER 95
- I CE 97
- SERVICE CONTROL LEVER 101
- - ATTENTION: 101
- Proportional services 103
- Alarm re-entry push button 105
- VEHICLE FUNCTIONS SELECTOR 107
- REVOLVING LIGHT SWITCH 113
- BOOM HEAD SOLENOID VALVE 115
- (OPTIONAL) 115
- FRONT HOOK 119
- AXA 1432 122
- USER INSTRUCTIONS AND 131
- GETTING TO KNOW THE VEHICLE 131
- INTEGRATED DEVICES 131
- “CENTRAL DASHBOARD” 131
- 891211 7 6 133
- I CEL 135
- (fig.207/C) 139
- (fig.208/C) 139
- ERRORS LIST 141
- Description What to do 145
- MAINTENANCE AND 147
- REGISTRATION 147
- MAINTENANCE PRESCRIPTIONS 149
- MANUFACTURER 151
- IDENTIFYING THE VEHICLE PARTS 153
- DO NOT USE 158
- SYNTHETIC-BASED OIL 158
- PARKING BRAKE 161
- Epicycloidal reduction gear 175
- (fig.57/D) 177
- (fig.69/D) 181
- 4.8 5.8 6.8 8.8 10.9 12.9 186
- 60° oval insert - BSP thread 188
- TROUBLESHOOTING 189
- TROUBLE SHOOTING 191
- MACHINE DETAILS 193
- AND MAINTENANCE WORK 195
- - ATTENTION 197
- ELECTRICAL DIAGRAMS 207
- AND CIRCUITS 207
- NAME DESCRIPTION SHEET 209
- WIRE COLOURS 213
- Valid certified 215
- HYDRAULIC CIRCUIT 223
- DIRECTIVE “ 225
- HYDRAULIC PLANT KEY 227
- TECHNICAL DATA 229
- TECHNICAL FEATURES 229
- Apollo 25.6 230
- (in seconds) 231
Manuais e produtos relacionados com Impressoras de rótulos CAB Apollo 1
Impressoras de rótulos CAB A8+ Manual do Operador
(120 páginas)
(120 páginas)
Impressoras de rótulos CAB A8+ Manual do Utilizador
(11 páginas)
(11 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais